What does it look like on your unit?

Yirro-plus® fits perfectly into the 15 mm slot of the A-dec delivery, by use of the standard included docking adaptor.

EXTEND YOUR DELIVERY
No spare 15 mm slot available? Ask your A-dec technician for spare part no. 99.06.52.03, an extension part containing a 15 mm slot; the Yirro-plus® docking adaptor is adapted for this slot.

INSTALLATION ON A-DEC
A-dec provides exterior air connection points, so it is very easy to plug-in the Yirro-plus® COMFORT system by use of the included Q.D. polymale connector. For Yirro-plus® PREMIUM you may need to consult your technician, in order to have the electricity properly connected.

NOTE – A-dec units have electrical sources placed somewhat further away from the assistance unit – due to which a longer connection hose is necessary. Ask your technician to order a PREMIUM start set with special article 0781 (white Air Power/box with longer connection hose). When ordered timely in advance, your start set will contain a longer hose (2.60 m) instead of the standard length (1,8m).

ACE – two mounting options
The ACE delivery has a relatively flat side, where you can mount the Universal Docking (included in start set). Choose a position that is well in reach.

C1 docking adaptor in smallest slot
Alternatively, the smallest slot can be used (most left one) to integrate the air-regulator by use of a C1 docking adaptor. Check if your small slot has a little square slid. Ask your distributor for article 0491.

Not yet available.

Most Anthos delivery units have a flat vertical side on which the universal docking can be mounted, which is standard included in the start set.

The Universal Docking is included in all start sets and it is practically always possible to mount this universal docking on a vertical surface at the side of the delivery unit. Even in case of a small brim.

OCCASIONAL INTEGRATION ANTHOS
You can check on occasion, if the standard docking adaptor (included in the start set) fits into the smallest slot (if available).

Belmont deliveries have a large flat side, on which it is easy to mount the universal docking (included in the start set).

INSTALLATION ON BELMONT
Belmont provides exterior air connection points, so it is very easy to plug-in the COMFORT system. For PREMIUM you will need to consult your technician, in order to have the electricity properly connected.

TUBE MOUNTING OPTION
You can mount the Yirro-plus® system on the instrument tube of a CART by use of the TUBE docking holder. The TUBE docking holder fits over a CART tubes with a diameter of ø13 mm. Mount it on the left side if you are right-handed and on the right side if you are left-handed.
NOTE: The TUBE docking holder is not standard included in the start set and needs special ordering. [Article 0291].

ORDER A LONGER SILICONE HOSE
If you mount Yirro-plus® on the instrument side, you will need a longer thin ø4 mm silicone hose for your Yirro-plus® mirror. Extra length is needed to transfer the mirror under the patients head, to the non-dominant side. Make sure to order a longer silicone hose [1.80 m – article 0279] along with your start set! Silicone hoses can be ordered separately as a spare part. Regular silicone hose [1.30 m length] have article number 0278.

INSTALLATION ON A CART
Most CARTS have accessible exterior air connection points, so it is very easy to plug-in the COMFORT system. Pay attention however: the Yirro-plus® system will need 3-6 bar (45-90 PSI) air compression and not all CARTS offer this. For PREMIUM you may need to consult your technician, in order to have the electricity properly connected.

ON THE SWIVEL ARM, NEAR THE SUCTION
Epilux has a swivel/bracket arm with a ø22 mm tube holding the delivery unit. It is most practical to mount the Yirro-plus® system by use of the TUBE docking holder.

The TUBE docking holder is not standard included in the start set and needs special ordering [article 0291].

IN FREE SLOT OF FEDESA
The examples below show two options for mounting of the Yirro-plus® on a Fedesa delivery unit.

Some units have a flat side surface (see indicated arrow), where you can mount the Universal docking, which is standard included in the start set.

Others types are rounded at all sides, which makes it difficult to mount a Universal Docking. You can create an option to dock your Yirro-plus system by use of a Desk-top Docking holder as shown below. The Desk-top docking is not standard included in the start set and needs special ordering [article 0584].

FINNDENT DELIVERY MOUNTING OPTIONS
The Finndent delivery units have limited option for side mounting and integration. See below for an impression.

Yirro-plus® FLEX coupling
Finndent units support the integration of Yirro-plus in the instrument panel. This means that you can use the Yirro-plus mirror together with an instrument. If you are interested in having Yirro-plus completely integrated in your instrument set, ask your Finndent dealer for the Yirro-plus® FLEX coupling. This is a special version of the Yirro-plus® magnet coupling that is developed to be built in the Finndent instrument unit. See below for an impression.

INTEGRATION INTO A FREE SLOT
By use of the C1 docking adaptor, it is possible to integrate the Yirro-plus® system into the smallest free slot.

The C1 docking adaptor is not standard included in the start set and needs special ordering [article 0491].

HEKA-UNIC / HEKA-UNICLINE-S
Yirro-plus® can be integrated in the delivery of HEKA-UNIC and of HEKA-UNICLINE-S, by use of the dedicated HEKA-UNIC-S docking adaptor. This docking adaptor is not standard included in the start set and needs special ordering [article 0323].

HEKA-UNICLINE
For the HEKA-UNICLINE units, you can make use of the dedicated HEKA-UNICLINE docking adaptor. In case that all three slots are occupied, you can create a fourth slot by mounting a HEKA-UNICLINE-SIDE adaptor. These docking adaptors are not standard included in the start set and need special ordering [article 0405 – HEKA UNICLINE docking adaptor; article 0499 – HEKA UNICLINE SIDE docking adaptor].

CONNECTION
HEKA offers very easy connection for electricity, on the back side of the unit there are free sockets available where the Yirro-plus® power adaptor can be plugged in. The connection hose can be guided to the delivery by (creating) a small hole in the unit base, down below.

SIDE MOUNTING for KaVo
For KaVo, we recommend side mounting by use of the Universal docking holder, that is standard included in each start set.

MIDMARK INTEGRATION
For Midmark, the dedicated C2 docking adaptor is available to integrate the system into a free slot.

The Midmark adaptor [article 0517] is not standard included in the start set and needs special ordering.

MORITA SIDE MOUNTING
Most Morita delivery units have flat vertical sides that enable mounting of the Universal Docking, included in the start set.

INTEGRATION INTO NEW IDEM (ALFA)
The standard docking adaptor (included in start set) fits into the outer slots of New Idem (Alfa). [Pay attention, underneath is a bit too much space and this causes the docking to waggle. This can be solve by use of a docking fixation ring [article 0532]. The docking fixation ring is not standard included in start sets.

OMS MOUNTING
As shown below, most delivery units of OMS have a flat vertical side and it is possible to mount the Universal Docking (standard included) onto the side.

INTEGRATED IN SMALLEST SLOT
Alternatively, sometimes you can use the C1 docking adaptor for integration into a spare slot. Look for the smallest slot and see if the square slid is present. The C1 docking adapter then will fit into the slot.

PELTON & CRANE mounting
Pelton & Crane delivery units tend to be rounded at all sides. By use of the Desk-top docking holder, you can however mount the Yirro-plus system.

The Desk-top docking holder is not standard included in the start set and needs special ordering [article 0584].

PLANMECA INTEGRATION
For integration into the most recent Planmeca Compact, the Planmeca SIDE docking holder is available. Simply plug it into the two holes on the side of the delivery and you can easily clip on the Yirro-plus® Universal Docking.

The Planmeca SIDE docking is not standard included in the start set and needs special ordering [article 0464].

SLOT INTEGRATION
It is also possible to place the docking in the spare slot (if available) by use of the Planmeca-1 Docking [article 0758].

The Planmeca-1 docking also fits on the slots of the Planmeca I-touch.
If all three slots are occupied, you can also use a TUBE docking to mount the system on the base tube of the delivery.

ALTERNATIVE MOUNTING PLANMECA
As an alternative, there are users that place the docking station on the instrument set:

SIRONA MOUNTING OPTIONS
Sirona far out shows the most differences in delivery units. But in all cases, there is a possibility to integrate or mount Yirro-plus onto the delivery. A summary:

SIRONA INTEGO
For the Sirona Intego delivery, a dedicated Sirona INTEGO docking adaptor is available [article 0720, not included in start set.]

SIRONA SINIUS
For Sirona Sinius delivery units, two options are available:
1) Use the Sirona C245+ docking adaptor to integrate in a free slot, see below picture. The Sirona C245+ docking adaptor is not standard included in the start set but needs separate ordering [article 0473]

2) Side mounting by use of Universal docking
Alternatively, you can mount the Universal docking (standard included) at the flat side of the Sinius delivery unit. See picture below:

SIRONA TENEO/SIRONA C3+
A good solution for Sirona TENEO and Sirona C3+ is to make use of the Mobile EXTENSION docking holder; this docking holder overcomes the long brim/overhang at the delivery’s side and thus enables vertical side docking. The Universal docking (standard included) can be clipped onto the Mobile Extension docking holder. See picture below for an impression:

The Mobile Docking EXTENSION is not standard included and needs separate ordering [article 0330].

SIRONA C4+/C5+
For Sirona C4+ and C5+, the SIRONA C245+ adaptor can be used in the small slot, see below picture.

SIRONA C2+
For the SIRONA C2+, two options are possible:
1) Use of the standard included adaptor docking in the smallest slot (when available). See below image:

2) Use of the Sirona C245+ adaptor in the second smallest slot (if available). The Sirona C245+ docking adaptor is not standard included and needs special ordering [article 0473].

SIRONA C8+
The Sirona C8+ has a flat side brim that is high enough to mount the Universal docking [standard included] onto. See picture below.

The italian Smart & Simple units have a delivery with a small slot. The standard docking adaptor (standard included in start set) fits into this slot. See image below:

STERN WEBBER – SIDE MOUNTING
Stern Webber delivery units in most cases have a flat side on which the standard included Universal docking can be mounted. The Universal docking is standard included in the start set.

STOMADENT MOUNTING
Most Stomadent delivery units have a flat side on which you can easily mount the Universal Docking holder (standard included in start set).

TRIDEC MOUNTING OPTIONS
The Tridec units use Cattani suction systems. Below, for 2 types of TRIDEC deliveries, an option is given:

CS90 spittoons
For these spittoons, it is possible to mount the standard included Universal docking at the flat side. See image below:

DSM spittoons
DSM spittoons have all rounded sides and the only docking holder that can be used is the Desk-top docking holder [1]. Alternatively, the use of the TUBE docking holder can be an option on the tube [2]. See below for an impression of these positions:

ULTRADENT MOUNTING
Ultradent delivery units have a flat side, on which it is easy to mount the Universal Docking (standard included in the start set). See below image for an impression:

Other example of flat sided deliveries:

Q-DENT MOUNTING
The Q-Dent unit makes use of the DURR block and this enables both side mounting and integration. For the side mounting, simply mount the standard included Universal Docking onto the side of the delivery.

For integration, you can use the standard docking adaptor, that is also included in the start set. An impression of the integrated option is given below:

VITALY INTEGRATION
Below is an impression of a Vitaly delivery unit. It is possible to mount the Universal Docking (included in start set) at the side.

Alternatively, if the small slot on the right is available, you could use the C1 docking [article 0491] to integrate the docking station. Check for the presence of the square slid in the slot.

XO MOUNTING
The best option for XO to mount the Yirro-plus system is on the flat front of the delivery unit. Depending on the type of XO-unit, you can make use of the XO-1 docking holder or XO-2 docking holder. See below for an impression of these docking holders. The more recent XO-units offer enough space to directly mount the Universal docking on it.

XO-1 docking holder [article 0750]
This docking holder was developed for the elder type of XO-units.

XO-2 docking holder [article 0548]
This docking holder has been developed for the most recent XO unit.

Alternatively to the above shown options, some users prefer to mount the Universal docking simply on the base of the chair. Make sure the docking is within reach.

Most Yoshida units have the following delivery:

You can use a Desk-Top docking holder to mount the Yirro-plus® system on this delivery. See below for an impression: